Canon imageCLASS MF8170c Manual do Utilizador

ColorimageCLASS MF8170cNetwork Guide

Network Connection Diagram1-2Before You Start1Network Connection DiagramRefer to the following diagram examples to confirm the network environment tha

CHAPTERTCP/IP Network Setup Procedures2-12Specifying the Network SettingsThis chapter describes the settings and procedures necessary to connect and u

TCP/IP Network Setup Procedures2-2Specifying the Network Settings2•If you are printing using a TCP/IP network, you can use the following print protoco

Preparation for Protocol Settings2-3Specifying the Network Settings2Preparation for Protocol SettingsBefore you specify the machine’s protocol setting

Preparation for Protocol Settings2-4Specifying the Network Settings2Settings from the Operation PanelIMPORTANTSettings specified from the operation pa

Preparation for Protocol Settings2-5Specifying the Network Settings25Press [ (-)] or [ (+)] to select <SUBNET MASK> ➞ press [Set].6Enter the num

Preparation for Protocol Settings2-6Specifying the Network Settings2Checking the Current Network SettingsYou can check the network settings of the mac

Preparation for Protocol Settings2-7Specifying the Network Settings23Execute the applicable command below to set the IP address for the network board.

Preparation for Protocol Settings2-8Specifying the Network Settings25Right-click the selected device ➞ click [Initial Settings] on the pop-up menu.6In

Preparation for Protocol Settings2-9Specifying the Network Settings2[Subnet Mask]: Enter the subnet mask used for the TCP/IP network.[Broadcast Addres

Manuals for the MachineThe manuals for this machine are divided as follows. Please refer to them for detailed information.Depending on the system conf

Protocol Settings2-10Specifying the Network Settings2Protocol SettingsYou can specify the machine’s protocol settings on the computer by using any of

Protocol Settings2-11Specifying the Network Settings2IMPORTANT•For your web browser, use Internet Explorer 5.01 SP1 or later, or Netscape Navigator 6.

Protocol Settings2-12Specifying the Network Settings23Under [Device Manager] in the left column of the screen ➞ click [Network].The [Network] page is

Protocol Settings2-13Specifying the Network Settings25Specify the setting method for the machine IP address. To use [Use DHCP], [Use BOOTP], and [Use

Protocol Settings2-14Specifying the Network Settings29Click [OK].The settings become valid after you restart the machine.The protocol settings are com

Setting Up a Computer for Printing2-15Specifying the Network Settings2Setting Up a Computer for PrintingAfter you have completed the protocol settings

Setting Up a Computer for Printing2-16Specifying the Network Settings2Printer Connection Method (LPD/Raw)Windows 98/Me1Press [Menu].2Press [ (-)] or [

Setting Up a Computer for Printing2-17Specifying the Network Settings2Windows 2000/XP1Press [Menu].2Press [ (-)] or [ (+)] to select <NETWORK SETTI

Setting Up a Computer for Printing2-18Specifying the Network Settings26If you are using LPD, change the port configuration information.❑ Click the [Po

Setting Up a Computer for Printing2-19Specifying the Network Settings2Print Server SettingsIf Windows 2000/XP/Server 2003 is on your network, the foll

How the Manual Is OrganizedBefore You StartSpecifying the Network SettingsAppendixIncludes troubleshooting, network settings, software information, th

Setting Up a Computer for Printing2-20Specifying the Network Settings2When the alternate driver is installed, additional windows will open for enterin

Printer Management2-21Specifying the Network Settings2Printer ManagementThe machine enables you to use any of the following software to check the stat

Printer Management2-22Specifying the Network Settings2Printer Management Using NetSpot ConsoleNetSpot Console is utility software capable of managing

Additional Protocol Settings2-23Specifying the Network Settings2Additional Protocol SettingsThis section describes two additional protocols supported

Additional Protocol Settings2-24Specifying the Network Settings2SNMPThe SNMP helps you monitor the state of the machine and collects its information.

Additional Protocol Settings2-25Specifying the Network Settings210Press [ (-)] or [ (+)] to select <ON> or <OFF> ➞ press [Set].11Press [St

Additional Protocol Settings2-26Specifying the Network Settings2

CHAPTERTroubleshooting3-13AppendixThis chapter describes how to resolve printing problems, network setting items and software for doing so, the glossa

Troubleshooting3-2Appendix3• Confirm that the proper printer driver is installed. Check if you are printing from Windows 98/Me, each computer must hav

Network Setting Items3-3Appendix3Network Setting ItemsNetwork Setting Items Using the Operation PanelYou can change the settings of the machine with t

ivContentsPreface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .viHow to Use This

Network Setting Items3-4Appendix3 Common SettingsNOTEItems with an asterisk (*) cannot be set using NetSpot Device Installer. Items with asterisks (*

Network Setting Items3-5Appendix3 TCP/IP SettingsItem Setting DescriptionDefault SettingUse DHCPWhether DHCP is used in setting the IP address (Off)U

Available Software for Network Settings3-6Appendix3Available Software for Network SettingsYou can specify the network settings of the machine using th

Glossary3-7Appendix3GlossaryBandingSpecifies the method for the Banding operation performed in the printer driver. As Banding defines the output image

Glossary3-8Appendix3File serverA personal computer or workstation to which two or more users on client personal computers can gain access via a local

Glossary3-9Appendix3ProtocolA set of rules that govern the transmission of data across a network. Examples of protocols are FTP, DHCP, BOOTP, RARP, IP

Glossary3-10Appendix3rates, the buffer provides a waiting station where the data can wait until the device for which it is meant is ready to access it

Index3-11Appendix3IndexAAdministrator Mode, 2-11ARP Table, 2-6ARP/PING Commands, 2-3, 2-6, 3-6Available Software Network Settings, 3-6BBanding, 3-7BOO

Index3-12Appendix3NNetSpot Console, 2-1, 3-3, 3-6Network Setting Items, 3-3NETWORK SETTINGS, 3-3OOperation Panel, 2-4, 3-3PPing, 2-7Preparation for Pr

vChapter 3 AppendixTroubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-1Network Settin

viPrefaceThank you for purchasing the Canon Color imageCLASS MF8170c. Please read this manual thoroughly before operating the machine in order to fami

viiDisplays Used in This ManualThe keys or buttons which you should press are marked with , as shown below.When multiple buttons or keys can be pres

viiiTrademarksCanon, the Canon logo, imageCLASS and NetSpot are trademarks of Canon Inc.Microsoft, MS-DOS, the Windows logo, Windows, are registered t

CHAPTERSystem Environment Requirements1-11Before You StartThis chapter describes what you need to know before you start using the machine in a network